Tempress Technologies

News, Events and Video

Stay Tuned…

December 30, 2016 | by JK Admin
Dr. Jack Kolle will be presenting at industry conferences in 2017. The conferences and presentation topics will be posted here once finalized.

Record Number 66 Plugs Drilled in Permian Basin Well in a Single Run with a HydroPull™

December 30, 2016 | by JK Admin

Spraberry Trend, Midland County, TX

Casing 5 1⁄2” 20 lb
KOP 8,400 ft. TVD; PBTD 19,331 ft. MD 2-5⁄8” Coil Tubing
66 Composite Plugs

This record job with a major Permian Basin operator involved milling out a total of 66 composite bridge plugs from a 10,000 ft. lateral in a 19,331 ft. MD horizontal well. The liner was 5-1⁄2” and the job was run on 2-5⁄8” CT. The 3-1⁄8” BHA consisted of a motor head assembly, hydraulic disconnect, screen sub, 3-1⁄8” High Flow-High Impact Tempress HydroPull™, 3-1⁄8” Oil States Energy Services motor and a 4-5⁄8” tri-cone rock bit. Water with friction reducer was pumped at 3.5 bpm increasing to nearly 4.0 bpm towards the end of the lateral. The wellhead pressure ranged from 1300 to 2650 psi and the pump pressure ranged from 3400 to 5700 psi. All 66 plugs were milled without incident and gel sweeps and short trips were utilized to ensure a good cleanout of well debris. This job was completed in a single HydroPull™ run with an average plug milling time of 9 minutes per plug.

screen-shot-2016-12-30-at-8-54-39-am

65 Composite Plugs Drilled in Permian Basin in a Single Run with a HydroPull™

December 30, 2016 | by JK Admin

Spraberry Trend, Midland County, TX

Casing 5 1⁄2” 20 lb
KOP 8,400 ft. TVD; PBTD 19,163 ft. MD 2-5⁄8” Coil Tubing
65 Composite Plugs

This near record well cleanout involved milling out a total of 65 composite bridge plugs from a lateral nearly 10,000 ft. long in a 19,163 ft. MD horizontal well. The liner was 5-1⁄2” and the job was run on 2-5⁄8” CT. The 3-1⁄8” BHA consisted of a motor head assembly, bi-directional jar, hydraulic disconnect, screen sub, 3-1⁄8” High Flow-High Impact Tempress HydroPull™, 3-1⁄8” Oil States Energy Services motor and a 4-5⁄8” tri-cone rock bit. Water with friction reducer was pumped at 3.5 bpm increasing to 4.5 bpm towards the toe of the lateral. The wellhead pressure ranged from 1,350 to 2,000 psi and the pump pressure ranged from 3,900 to 5,600 psi. All 65 plugs were milled without incident and gel/pipe-on-pipe sweeps and short trips were utilized to ensure a good cleanout of sand and plug debris. This job was completed in 94 hours in a single HydroPull™ run with an average plug milling time of 10 minutes per plug.

screen-shot-2016-12-30-at-8-50-58-am

50 Composite Plugs Drilled in Midland Basin in a Single Run with a HydroPull™

December 30, 2016 | by JK Admin

Spraberry Trend, Midland County, TX

Casing 5 1⁄2” 20 lb
KOP 8,250 ft. TVD; PBTD 20,277 ft. MD 2-5⁄8” Coil Tubing
50 Composite Plugs

This well cleanout involved milling a total of 50 composite bridge plugs from a horizontal lateral almost 10,000 ft. long to a total measured depth of 20,277 ft. The liner was 5-1⁄2” and the job was run on 2-5⁄8” coiled tubing. The 3-1⁄8” BHA consisted of a motor head assembly, dual back pressure valve, hydraulic disconnect, screen sub, 3-1⁄8” High Flow-High Impact Tempress HydroPull™, 3-1⁄8” Oil States Energy Services motor and a 4-5⁄8” tri-cone rock bit. Water with pipe-on-pipe friction reducer was pumped at 4.0 bpm increasing to 4.5 bpm towards the toe of the lateral. Nitrogen was commingled with fluid after the 34th plug and continued to near TD. All 50 plugs were milled without any short trips and 5-20 bbl gel sweeps followed the milling of each plug. The wellhead pressure ranged from 80 to 500 psi and the pump pressure ranged from 2,900 to 3,700 psi. This job was completed in 45 hours with a single High Flow-High Impact HydroPull™ with an average plug milling time of 5 minutes per plug.screen-shot-2016-12-30-at-8-48-47-am

65 Composite Plugs Drilled in Midland Basin with Oil States Motors and a HydroPull™

December 30, 2016 | by JK Admin

Spraberry Trend, Midland County, TX

Casing 5 1⁄2” 20 lb
KOP 9,031 ft. TVD; PBTD 19,760 ft. MD 2-5⁄8” Coil Tubing
65 Composite Plugs

Oil States motors and the Tempress HydroPull™ milled a total of 65 composite bridge plugs from a horizontal lateral almost 10,000 ft. long to a total measured depth of 19,760 ft. The liner was 5-1⁄2” and

the job was run on 2-5⁄8” coiled tubing. The 3-1⁄8” BHA consisted of a weld-on coil connector, a dual back pressure valve, a set of jars, a hydraulic disconnect, a ball-actuated annular velocity tool, a screen sub, a 3-1⁄8” High Flow-High Impact Tempress HydroPull™, a 3-1⁄8” Oil States Energy Services motor and a 4-5⁄8” tri-cone rock bit. Water with pipe-on-pipe friction reducer was pumped at 4.0 bpm increasing to 4.75 bpm during the final sweep and just prior to pulling out of the hole. All 65 plugs were milled while utilizing four 1,000 ft. short trips and two short trips to the vertical section to ensure adequate hole cleaning and debris removal. Gel sweeps in volumes ranging from and 5-10 bbl followed the milling of each plug. The wellhead pressure ranged from 1,300 to 1,700 psi and the pump pressure ranged from 2,900 to 4,700 psi. This job was completed in 128 hours, including a cautionary round trip due to wire pieces discovered in the plug catchers. The average plug milling time was 13 minutes per plug.screen-shot-2016-12-30-at-8-43-35-am

64 Composite Plugs Drilled in Midland Basin in a Single Run with a HydroPull™

December 30, 2016 | by JK Admin

Wolfcamp Trend, Midland County, TX

Casing 5 1⁄2” 20 lb
KOP 8,300 ft. TVD; PBTD 18,674 ft. MD 2-5⁄8” Coil Tubing
64 Composite Plugs

This impressive well cleanout involved milling out a total of 64 composite bridge plugs from a lateral nearly 10,000 ft. long in an 18,674 ft. MD horizontal well. The liner was 5-1⁄2” and the job was run on 2-5⁄8” CT. The 3-1⁄8” BHA consisted of a motor head assembly, dual back pressure valve, hydraulic disconnect, screen sub, 3-1⁄8” High Flow-High Impact Tempress HydroPull™, 3-1⁄8” Oil States Energy Services motor and a 4-5⁄8” tri-cone rock bit. Water with friction reducer was pumped at 4.25 bpm increasing to 5.0 bpm towards the toe of the lateral. All 64 plugs were milled without incident and 10 bbl gel sweeps followed the milling of each plug. Two short trips were utilized to ensure a good cleanout of sand and plug debris, including one trip to vertical after milling the 46th plug. The wellhead pressure ranged from 250 to 420 psi and the pump pressure ranged from 2,800 to 4,250 psi. This job was completed in a single HydroPull™ run in 57 hours with an average plug milling time of 5 minutes per plug.

screen-shot-2016-12-30-at-8-28-30-am

72 Plugs Drilled in a Single Run with a HydroPull™

December 13, 2016 | by JK Admin

Case Study, Permian Basin, TX

Casing 4 ½” 13.5 lb/ft
Lateral Length 8,585 ft. to 17,903 ft.
Jointed Pipe – Workover Rig
72 Composite Frac Plugs

 

After an unconventional oil well was drilled in the Permian Basin, the operator ran 4 ½”, 13.5 lb/ft casing to a depth of nearly 18,000 ft. MD. After the wellbore was prepared for fracturing, a plug and perf method was used to complete the well. A total of 72 Composite Frac Plugs were placed at spaced intervals in the horizontal wellbore from 8,585 ft. MD to 17,903 ft. MD.

The operator utilized a workover rig and jointed pipe for conveying the BHA. The 2 ⅞” OD BHA consisted of a dual flapper valve assembly, a hydraulic disconnect, a 2 ⅞” OD High Flow-High Impact Tempress HydroPull, a 2.8” OD Baker Hughes Navi-Drill™ X-treme mud motor and a 3 ¾” OD Baker Hughes butterfly mill dressed with Glyphaloy™ carbide cutting structure.

Past operations possessing similar lateral lengths typically required multiple trips to change out BHA components. This record-setting job involved milling out a total of 72 composite frac plugs from a 9,318 ft. lateral in a 17,909 ft. MD horizontal well without incident and in a single HydroPull run. The average plug milling time was 20 minutes per plug and the operator saved 30 hours of rig time, saving extra BHA charges by eliminating a second trip to replace BHA components.